Siemens ET 200SP HA, EX-DQ 2x23,1VDC/20MA; 6DL1132-6EB00-0HX1
SIMATIC ET 200SP HA, ET 200SP, digital ex-i output module, Ex-DQ 2x23,1VDC/20mA suitable for BaseUnit type X1, channel diagnostics...
Price on request
| SIMATIC ET 200SP HA, ET 200SP, digital ex-i output module, Ex-DQ 2x23,1VDC/20mA suitable for BaseUnit type X1, channel diagnostics |
| General information | |
| Product type designation | Ex-DQ 2x23.1VDC/20mA |
| Firmware version | V1.0 |
| ● FW update possible | Yes |
| usable BaseUnits | BU type X1 |
| Product function | |
| ● I&M data | Yes; I&M0 to I&M3 |
| ● Isochronous mode | No |
| Engineering with | |
| ● STEP 7 TIA Portal configurable/integrated from version | STEP 7 V16 or higher with HSP |
| ● STEP 7 configurable/integrated from version | STEP 7 V5.6 SP2 or higher |
| ● PCS 7 configurable/integrated from version | V9.1 |
| Operating mode | |
| ● DQ | Yes |
| ● MSO | Yes |
| Redundancy | |
| ● Redundancy capability | No |
| Input current | |
| Current consumption (rated value) | 80 mA; At 20 mA per channel |
| Current consumption, max. | 80 mA; At 20 mA per channel |
| output voltage / header | |
| Rated value (DC) | 23.1 V; See output characteristic in manual |
| Power loss | |
| Power loss, typ. | 1.3 W |
| Address area | |
| Address space per module | |
| ● Address space per module, max. | 1 byte; + 1 byte for QI information |
| Hardware configuration | |
| Automatic encoding | |
| ● Mechanical coding element | Yes |
| Selection of BaseUnit for connection variants | |
| ● 2-wire connection | BU type X1 |
| Digital outputs | |
| Number of digital outputs | 2 |
| Current-sinking | No |
| Current-sourcing | Yes |
| Digital outputs, parameterizable | Yes |
| Short-circuit protection | Yes |
| Open-circuit detection | Yes; capacitive loads can cause wire-break diagnostics when the channel is switched off |
| Overload protection | Yes |
| Limitation of inductive shutdown voltage to | DQ.n- (-1 V) |
| Switching capacity of the outputs | |
| ● with resistive load, max. | 20 mA; See output characteristic in manual |
| ● with inductive load, max. | 20 mA; See output characteristic in manual |
| Load resistance range | |
| ● lower limit | 872 Ω; See output characteristic in manual |
| ● upper limit | 10 kΩ; See output characteristic in manual |
| Output current | |
| ● for signal "1" rated value | 20 mA |
| ● for signal "0" residual current, max. | 100 µA; 250 µA test current for wire break diagnostics |
| Output delay with resistive load | |
| ● "0" to "1", typ. | 50 µs |
| ● "1" to "0", typ. | 100 µs |
| Parallel switching of two outputs | |
| ● for uprating | No |
| Switching frequency | |
| ● with resistive load, max. | 500 Hz |
| ● with inductive load, max. | 500 Hz |
| Total current of the outputs | |
| ● Current per channel, max. | 20 mA |
| ● Current per module, max. | 40 mA |
| Total current of the outputs (per module) | |
| horizontal installation | |
| — up to 70 °C, max. | 40 mA |
| vertical installation | |
| — up to 60 °C, max. | 40 mA |
| Cable length | |
| ● shielded, max. | 500 m; Ex characteristic values must be observed |
| ● unshielded, max. | 500 m; Ex characteristic values must be observed |
| Interrupts/diagnostics/status information | |
| Diagnostics function | Yes |
| Substitute values connectable | Yes |
| Alarms | |
| ● Diagnostic alarm | Yes |
| ● Maintenance interrupt | Yes |
| Diagnoses | |
| ● Diagnostic information readable | |
Similar products:
Siemens ET 200SP, DQ 4x24VDC/2A High Speed, PU 1; 6ES7132-6BD20-0DA0
SIMATIC ET 200SP, digital output module, DQ 4x 24 V DC/2A High Speed, Pack quantity: 1 unit suitable for BU type A0, Color code CC00, 3 alternative operating modes:
-
(Out of stock)
Price on request
Siemens ET 200SP, DQ 8x 24VDC/0,5A SINK BA, PU 1; 6ES7132-6BF61-0AA0
SIMATIC ET 200SP, Digital output module, DQ 8x 24V DC/0,5A Sink Basic, Sink output (NPN, M-switching), Packing unit: 1 piece, fits to BU-type A0, Colour Code CC01,
-
(Out of stock)
Price on request
Siemens ET 200SP, DQ 4x24..230VAC/2A HF, PU 1; 6ES7132-6FD00-0CU0
SIMATIC ET 200SP, digital output module DQ 4x 24..230V AC/2A HF packaging unit: 1 piece, two alternative modes: DQ and power control, fits to BU-Type U0, color code
-
(Out of stock)
Price on request
Siemens ET 200SP HA, EX-DQ 2x17,4VDC/27MA; 6DL1132-6CB00-0HX1
SIMATIC ET 200SP HA, ET 200SP, digital ex-i output module, Ex-DQ 2x17,4VDC/27mA suitable for BaseUnit type X1, channel diagnostics
-
(Out of stock)
Price on request
Siemens ET 200SP, DQ 8x 24V DC/0,5A Basic, PU 1; 6ES7132-6BF01-0AA0
SIMATIC ET 200SP, Digital output module, DQ 8x 24V DC/0,5A Basic, Source output (PNP,P-switching) Packing unit: 1 piece, fits to BU-type A0, Colour Code CC02, substitute
-
(Out of stock)
Price on request
Siemens ET 200SP, DQ 4x24VDC/2A ST; 6ES7132-6BD20-0BA0
SIMATIC ET 200SP, digital output module, DQ 4x 24VDC/2A Standard, suitable for BU type A0, Color code CC02, Module diagnostics
-
(Out of stock)
Price on request