WEHO MDR-100-24
MDR-100-24 AC/DC 100w 24v DIN rail smps led power supply with CE ROHS Features: 1. AC input range selectable by switch 2. Protections: Short circuit / Overload /...
Out of stock
MDR-100-24 AC/DC 100w 24v DIN rail smps led power supply with CE ROHS
Features:
1. AC input range selectable by switch
2. Protections: Short circuit / Overload / Over voltage / Over temperature
3. 100% full load burn-in test
4. Low cost, high reliability
5. 24 months warranty| MODEL | MDR-100-12 | MDR-100-15 | MDR-100-24 | MDR-100-48 | |
| OUTPUT | DC VOLTAGE | 12V | 15V | 24V | 48V |
| RATED CURRENT | 7.5A | 6.7A | 4A | 2A | |
| CURRENT RANGE | 0 ~ 7.5A | 0 ~6.7A | 0 -4A | 0-2A | |
| RATED POWER | 100W | 100W | 100W | 100W | |
| RIPPLE & NOISE (max.) | 80mVp-p | 120mVp-p | 150mVp-p | 200mVp-p | |
| VOLTAGE ADJ. RANGE | 12 -13.2V | 15-16.5V | 24 - 26.4V | 48 ~ 56V | |
| VOLTAGE TOLERANCE | ±2.0% | ±1.0% | ±1.0% | ±1.0% | |
| LINE REGULATION | ±1.0% | ±1.0% | ±1.0% | ±1.0% | |
| LOAD REGULATION | ±1.5% | ±1.0% | ±1.0% | ±1.0% | |
| SETUP, RISE TIME Note.5 | 500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load | ||||
| HOLD UP TIME (Typ.) | 50ms/230VAC 20ms/115VAC at full load | ||||
| INPUT | VOLTAGE RANGE | 85 - 264VAC 120-370VDC | |||
| FREQUENCY RANGE | 47 ~ 63Hz | ||||
| EFFICIENCY (Typ.) | 78% | 86% | 88% | 87% | |
| AC CURRENT (Typ.) | 1.8A/115VAC 1A/230VAC | ||||
| INRUSH CURRENT (Typ.) | COLD START 30A/115VAC,60A/230VAC | ||||
| LEAKAGE CURRENT | <1mA/240VAC | ||||
| PROTECTION | OVERLOAD | 105 - 150% rated output power | |||
| Protection type: Constant current limiting, recovers automatically after fault condition is removed | |||||
| OVERVOLTAGE | 6.25-7.25V | 15.6 - 18V | 31.2-36V | 57.6 - 64.8V | |
| Protection type: Shut down o/p voltage, re-power on to recover | |||||
| FUNCTION | DC OK SIGNAL | Relay contact rating (max.): 30V/1A resistive | |||
| ENVIRONMENT | WORKING HUMIDITY | 20 ~ 90% RH non-condensing | |||
| STORAGE TEMP., HUMIDITY | -40 ~ +85°C, 10 ~ 95% RH | ||||
| TEMP. COEFFICIENT | ±0.03%/°C (0 - 50°C) | ||||
| VIBRATION | Component: 10 - 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 | ||||
| SAFETY &EMC | SAFETY STANDARDS | UL508, UL60950-1, TUV EN60950-1 approved | |||
| WITHSTAND VOLTAGE | l/P-0/P:3KVAC l/P-FG:2KVAC 0/P-FG:0.5KVAC | ||||
| ISOLATION RESISTANCE | l/P-O/P, l/P-FG, 0/P-FG:>100M Ohms/500VDC/25°C/70% RH | ||||
| EMC EMISSION | Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3 | ||||
| EMC IMMUNITY | Compliance to EN6100(M-2,3,4,5,6,8,11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A | ||||
| OTHERS | MTBF | 299.2K hrs min. MIL-HDBK-217F (25°C) | |||
| DIMENSION | 50*90*100mm (W*H*D) | ||||
| PACKING | 0.42Kg; 30pcs/20Kg/0.82CUFT | ||||
| NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature. | ||||
| 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1 uf & 47uf parallel capacitor. | |||||
| 3. Tolerance : includes set up tolerance, line regulation and load regulation. | |||||
| 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to "EMI testing of component power supplies. | |||||
| 5. 5.Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. | |||||